Loctite 406 Instant Adhesive 20g
4.7 (393) · € 7.50 · En stock
Loctite 406 Instant Adhesive 20g Shear Strength, Grit Blasted Steel : 3200 psi Temperature : -65 - 250 °F Viscosity : 20 mPa.s (cP) Brookfield Key Substrates : Plastics and Rubbers Color : Clear: Ultra Clear Curing Type : Humidity Application : Bonding LOCTITE® 406 is an instant adhesive designed especially for the fast bonding of plastics and rubbers. This product offers exceptionally low viscosity. When combined with LOCTITE primers for cyanoacrylates, it can also be used on difficult-to-bond plastics. Rapid bonding of plastic & rubber, including EPDM LOCTITE 770 or LOCTITE 7239 primer improves adhesion of difficult-to-bond substrates LOCTITE®406™ is designed for bonding of plastics andelastomeric materials where very fast fixturing is required.Commercial Item Description A-A-3097:LOCTITE®406™ has been qualified to Commercial ItemDescription A-A-3097. Note: This is a regional approval.Please contact your local Technical Service Center for moreinformation and clarification.TYPICAL
Loctite 406 Instant Adhesive 20g Shear Strength, Grit Blasted Steel : 3200 psi Temperature : -65 - 250 °F Viscosity : 20 mPa.s (cP) Brookfield Key Substrates : Plastics and Rubbers Color : Clear: Ultra Clear Curing Type : Humidity Application : Bonding
LOCTITE® 406 is an instant adhesive designed especially for the fast bonding of plastics and rubbers. This product offers exceptionally low viscosity. When combined with LOCTITE primers for cyanoacrylates, it can also be used on difficult-to-bond plastics. Rapid bonding of plastic & rubber, including EPDM LOCTITE 770 or LOCTITE 7239 primer improves adhesion of difficult-to-bond substrates
LOCTITE®406™ is designed for bonding of plastics andelastomeric materials where very fast fixturing is required.Commercial Item Description A-A-3097:LOCTITE®406™ has been qualified to Commercial ItemDescription A-A-3097. Note: This is a regional approval.Please contact your local Technical Service Center for moreinformation and clarification.TYPICAL CURING PERFORMANCEUnder normal conditions, the atmospheric moisture initiates thecuring process. Although full functional strength is developedin a relatively short time, curing continues for at least 24 hoursbefore full chemical/solvent resistance is developed.Cure Speed vs. SubstrateThe rate of cure will depend on the substrate used. The tablebelow shows the fixture time achieved on different materialsat 22 °C / 50 % relative humidity. This is defined as the time todevelop a shear strength of 0.1 N/mm².Cure Speed vs. Bond GapThe rate of cure will depend on the bondline gap. Thin bondlines result in high cure speeds, increasing the bond gap willdecrease the rate of cure.Cure Speed vs. HumidityThe rate of cure will depend on the ambient relativehumidity. The best results are achieved when the relativehumidity in the working environment is 40% to 60% at 22°C.Lower humidity leads to slower cure. Higher humidityaccelerates it, but may impair the final strength of the bond.Cure Speed vs. ActivatorWhere cure speed is unacceptably long due to large gaps,applying activator to the surface will improve cure speed.However, this can reduce ultimate strength of the bond andtherefore testing is recommended to confirm effect.GENERAL INFORMATIONThis product is not recommended for use in pure oxygenand/or oxygen rich systems and should not be selected asa sealant for chlorine or other strong oxidizing materials.For safe handling information on this product, consult theSafety Data Sheet (SDS).Directions for use:
Bond areas should be clean and free from grease. Cleanall surfaces with a Loctite®cleaning solvent and allow todry. To improve bonding on low energy plastic surfaces,Loctite® Primer may be applied to the bond area. Avoidapplying excess Primer. Allow the Primer to dry. LOCTITE® Activator may be used if necessary. Apply it toone bond surface (do not apply activator to the primedsurface where Primer is also used). Allow the Activator todry. Apply adhesive to one of the bond surfaces (do not applythe adhesive to the activated surface). Do not use itemslike tissue or a brush to spread the adhesive. Assemblethe parts within a few seconds. The parts should beaccurately located, as the short fixture time leaves littleopportunity for adjustment. LOCTITE®Activator can be used to cure fillets of productoutside the bond area. Spray or drop the activator on theexcess product. Bonds should be held fixed or clamped until adhesive hasfixtured. Product should be allowed to develop full strength beforesubjecting to any service loads (typically 24 to 72 hoursafter assembly, depending on bond gap, materials andambient conditions).
Loctite Material SpecificationLMS dated December-22, 2011. Test reports for each batchare available for the indicated properties. LMS test reportsinclude selected QC test parameters considered appropriate tospecifications for customer use. Additionally, comprehensivecontrols are in place to assure product quality andconsistency. Special customer specification requirements maybe coordinated through Henkel Quality.StorageStore product in the unopened container in a dry location.Storage information may be indicated on the product containerlabeling.Optimal Storage: 8 °C to 21 °C. Storage below 8 °C orgreater than 28 °C can adversely affect product properties.Material removed from containers may be contaminated duringuse. Do not return product to the original container. HenkelCorporation cannot assume responsibility for product whichhas been contaminated or stored under conditions other thanthose previously indicated. If additional information is required,please contact your local Technical Service Center orCustomer Service Representative.
Loctite 406 Prism Instant Adhesive
Loctite 40640 406 Prism Instant Adhesive, Surface Insensitive, 20 g, B –, loctite 406
20g Loctite 406 Super Glue Instant Adhesive Universal Type Sticky Plastic Rubber Quick-drying Glue
Loctite 406 Prism Instant Adhesive, Surface Insensitive
instant adhesive , loctite 495, loctite
Henkel Loctite 406 20g Instant Adhesive For Plastic and Rubber. LOCTITE 406 is an instant adhesive designed especially for the fast bonding of
Loctite 406 Instant Adhesive Super Glue for Plastic & Rubber 20g
This product is instant dry glue, strong and firm, not afraid of flooding. Clean the surface stains and apply glue to the bonded side. Fast gel, that
Loctite 406 Instant Adhesive Super Glue for Plastic & Rubber Henkel 20G US SALE
20g Loctite 406 Super Glue Instant Adhesive Universal Type Sticky Plastic Rubber Quick-drying Glue
Loctite 1919335 406 Instant Adhesive 20g
